Lantern Roof Installation FAQs
Straight answers to the questions we're asked most.
How much does a roof lantern cost to install in the UK?
A fitted roof lantern typically costs £1,200 to £2,200 for a small uPVC model and £2,500 to £4,500 for a medium aluminium lantern in the UK in 2026. Large or bespoke lanterns can cost £4,500 to £8,000 or more. Cutting a new opening into an existing roof usually adds £1,500 to £3,500 for structural and roofing work.
Can a roof lantern be fitted to an existing flat roof?
Yes, a roof lantern can be added to an existing flat roof. The roof is propped, an opening is cut, and joists are trimmed with doubled timbers to carry the load. A kerb is built and the roof membrane sealed around it. This usually needs Building Regulations approval and sometimes a structural calculation for larger openings.
Do I need planning permission for a roof lantern?
Many roof lanterns on single-storey rear extensions do not need planning permission, but it depends on the property and location. Conservation areas, listed buildings and lanterns that change the roof height significantly may need consent. Check with your local planning authority. Building Regulations requirements are separate and often apply.
Are roof lanterns prone to leaking?
Roof lanterns do not leak if they are installed properly. Most leaks come from badly built kerbs, poor membrane detailing at the corners, low upstands or failed seals on cheap older models. A level, square kerb at least 150mm above the roof, with the membrane properly dressed and sealed, is the key to a watertight lantern.
What is the difference between a roof lantern and a skylight?
A roof lantern is a pitched, three-dimensional glazed structure that sits above the roof, while a skylight or flat rooflight is a single flat or slightly sloped pane. Lanterns let in light from several angles and create a feeling of height inside. Flat rooflights have a lower profile and a more minimal, contemporary appearance.
Do roof lanterns make rooms too hot?
Roof lanterns can cause overheating on sunny days if standard clear glass is used, especially on south-facing roofs. Solar control glass reduces heat gain significantly while still letting in plenty of daylight. Some lanterns also offer opening vents, which help release warm air. Discuss orientation and glazing options with the installer before ordering.
How long does it take to install a roof lantern?
Fitting a lantern onto a ready kerb usually takes half a day to a day. Adding a lantern into an existing flat roof, including cutting the opening, trimming joists, building the kerb, sealing the roof and plastering inside, typically takes two to four days. Lanterns are made to measure, with lead times of around two to four weeks.
Aluminium or uPVC roof lantern: which is better?
Aluminium lanterns are stronger, so they have slimmer bars, larger glass and a sleeker look, and they come in more colours. uPVC lanterns are cheaper and perform well thermally but have chunkier bars. For large or design-led extensions aluminium is usually preferred, while uPVC is a good budget option for smaller rooms and garden rooms.
Can roof lanterns be opened?
Some roof lanterns include electrically operated opening vents that help ventilate kitchens and release warm air in summer. Many have rain sensors that close the vent automatically. Opening vents add cost and need a power supply, so plan wiring early. Fixed lanterns are simpler and cheaper, with ventilation provided by windows or extractor fans instead.
How big should a roof lantern be?
A common rule of thumb is for the lantern to cover around 20% to 30% of the room's floor area, centred over the main living or kitchen zone. It must also fit between structural joists or steels and leave enough roof around it for drainage. A lantern too large can cause overheating, while one too small looks lost.
How do you clean a roof lantern?
Roof lanterns are cleaned from outside using a soft brush or water-fed pole with plain water or a mild, non-abrasive cleaner. Self-cleaning glass reduces how often this is needed. Never walk on the glass. Inside, wipe frames and glass with a soft cloth. Check seals and keep the roof around the kerb clear of leaves.
Why is my roof lantern misting up?
Misting between the panes means the sealed unit has failed and moisture has got inside, which needs the glass unit replacing. Condensation on the inside surface is different and usually comes from high humidity in kitchens or bathrooms. Better ventilation, thermally broken frames and warm-edge spacers in the glazing reduce internal condensation significantly.
Get a free lantern roof installation quote
Tell us what you need and we'll come back with a clear price.
Request a quote